Comdial Back
Date/Time Changes
All Changes Must be Made from the Attendant's Station Phone
DXP, DXP Plus, FX series (Impact Classic and Impact SCS Phones):
ITCM, *, #, 0, *, 01, MM, DD, YY, HH, MM, #, SPKR to end


Executech, Executech II, or Centratech:
ITCM, *, #, YY, MM, DD, HH, MM
Executech XE:
ITCM, *, #, 01, YY, MM, DD, HH, MM, (Dial 1-7 for day of the week, where Sunday=1 and Saturday=7), MNTR or SPKR to end.
Executech 2000, Unisyn, DSU, DSUII, Americom, Express:
ITCM, *, #, 01, YY, MM, DD, HH, MM, SPKR to end
________________________________________
ESI IVX Back
1. Enter Programming Mode
Press PROG/HELP, PARK, 4, 5, 6, (or new Administrator password), #
TO EXIT: Hang Up
2. Press 1 for System Parameters
Press 4 to Set Date/Time
3. Enter new time in a twelve-hour format.
EXAMPLE: Enter 1233 for 12:33 or 315 for 3:15 ( No Leading Zeros)
4. Select AM or PM by pressing the scroll keys
5. Enter a new date in an eight-digit format, including leading zeros.
EXAMPLE: Enter 07042000 for July 4, 2000 (That leading zeros are required here unlike step 3)
________________________________________
Executone Back
Medley System
FROM ANY TELEPHONE PRESS MENU (OR F1) KEY
PRES PARK3 KEY (FAR RIGHT SOFT KEY)
ENTER PASSWORD ***#
PRESS 1 FOR SYSTEM FUNCTION PROGRAMMING
PRESS 4 TO SET TIME
ENTER TIME IN TWELVE HOUR FORMAT, PRESS #
PRESS PARK3 KEY TO INDICATE AM OR PM, PRESS # KEY TO CONFIRM
PRESS H/F KEY (OR REPLACE RECEIVER) TO HANG UP

ISOETEC SYSTEM ? 66 / 96 / 120
1. From the Main Operator Screen
- Press [CRTL] [P]
- Press [ESC] key
2. Screen will say "Enter Password" to go to main menu
If you know the PASS WORD enter it now or
Please, try: "PASSWORD or "P"
3. Press [B] for system programming
4. Press [T] cursor will move to Time section type in HHMM military time and hit [RETURN] or [ENTER] type in date (even if correct) and hit [RETURN] or [ENTER]
5. Press [ESC] key - screen will be back at main menu.
6. Press [E] to return to main operator screen.

________________________________________
IWATSU Back
If your Iwatsu telephone has a Clock button, press the Speaker button SPKR on your telephone followed by the Clock button and then enter the time in military (24 hour clock) format. Press the Speaker button SPKR to save your entry.
If your Iwatsu telephone does not have a clock button, go to an attendant telephone for your system. Press the Speaker button SPKR. Then press the Feature button FEAT and dial 64. Enter the time in military time (24 hour clock format) and press the Speaker button SPKR to save your entry.

________________________________________

Lucent Partner Systems (ACS, Endeavor, Partner Plus, Partner II) Back
All programming is done at ext. 10 or 11
1) Press feature key, then 00 (enters programming mode)
2) Press left intercom button twice
3) #103 (code to change system time)
4) Enter correct time (military time)
5) Press feature key, then 00 (exit programming)
LUCENT Merlin Legend R1 thru R7
From Main Menu
1. ? Press F1 or System Program
2. ? Press F5 or Exit
3. ? Press F1 or System
4. ? Press F8 or Time
5. ? Back Space Out Old Time and Enter New Time Using 24- hour Format
6. ? Press F10 or Enter
7. ? Press F5 or Exit
8. ? Press Home
LUCENT Definity
1. Type set time and press <return> (The Date and time screen appears)
2. Using a 24-hour clock, fill in the appropriate fields. For example, for 2:00 p.m., enter 14 in the hour field and 00 in the minute field
3. Press F3to save changes to system memory.
4. Type display time and press <return> to check the new date and time.
Note: When you change the date and time, some phone displays may not automatically refresh. End-users should press the date/time button on their phone and wait for the terminal to return to "normal" to update the display.
Note for versions G3 R7 and above:
In G3 R7 and above, there are additional fields on the "set/display time" screen. The "Type:" field should be set to standard or daylight savings, depending on which is currently correct. The "Daylight Savings Rule:" field is set to one of 17 rules (0-16) defined on the "change daylight-savings-rule" screen. These entries will automatically set the system time to comply with daylight savings time changes.
Additionally, in the G3r R7 and above with the Multiple Locations feature activated, the above time can be offset + or - on the "change location (1-44)" screen. This screen also allows a different daylight-savings-rule to be used when port networks (PNs) are located in different geographic areas. The location identifier (1-44) is associated with each PN on the "add/change cabinet" screen.
When you change the date or time, some display phones may not automatically refresh the display. If this happens, have each user press the date/time button on their phone and the display should update
________________________________________
Macrotel Telephone System Back

You must first enable the User Programming form any telephone with the following steps:
1. Press [#] [0] [4]
2. Press [4] [3] [2] [1] [1]
3. Press [#]
To set the time/date:
1. Press [#] [5] [5]
2. "YY MM DD W HH MM" will be displayed
3. Dial in the new data using the following list
4. Press [#]
• YY=last two digits of the year
• MM=month of the year
• DD=day of the month
• W=weekday
• 0=Sunday
• 1=Monday
• 2=Tuesday
• 3=Wednesday
• 4=Thursday
• 5=Friday
• 6=Saturday
• HH=hour (24-hour clock/military time)
• MM=minutes

________________________________________
NEC DS 1000 and 2000 Back
1. Go to extension 300. (Usually the reception phone.
Press 6 on any idle telephone and the extension number will appear in the display).
2. Press #TD (#83) for Time/Date.
3. Current time will appear in the display.
Enter time in 24-hour clock using the following format:
(HHMMSS) Hours (2 digits), Minutes (2 digits) and Seconds (2 digits)
4. Press HOLD
5. Current date will appear in the display.
If the date is correct you may press HOLD then SPK to exit programming OR
Enter date using the following format:
(MMDDYYYY) Month (2 digits), Day (2 digits) and Year (4 digits)
6. Press HOLD then SPK.
NEC Elite
Programming is done from first 2 station ports on system.
1. Press FNC key
2. Dial 9
3. Dial #
4. Dial current time (e.g. 03:29)
5. Press the RECALL key to toggle AM/PM
6. Press the HOLD key to advance to the calendar
7. Press the RECALL key to select the day of the week
8. Press the # key to move the cursor to the day of the month setting
9 Enter the day by using the dial pad
10. Press the RECALL key to select the month
11. Press the # key to move the cursor to the year setting
12. Enter the year by using the dial pad (only the last two digits are entered)
13. Press the FNC key

NOTE: if only setting the time, press the FNC key after making the changes


NORSTAR Back
There are a couple of different ways access the time change feature, depending on the type of system you have. A programming template is provided below if you need it. Just cut-out the shaded areas as well as around the outside of the template. Once cut, place the template over the top 2 rows of buttons on your 7310 or 7324 telephone (typically lines 1 and 2 on your telephone).
After you enter programming mode, all methods are pretty much the same.
Access type 1: Press * * TIME (8463)
Access type 2: Press * * ADMIN (23646)
System displays Password & enter 23646
Display shows 1.Sys speed dial
Press Next Display shows 2. Names
Press Next Display shows 3. Time and date
Press Show Display shows Time 16:24
On the Softkey under the display it says CHANGE
If you wish to change the time, press CHANGE, if not press NEXT
Once you pressed the CHANGE button the hour displays;
If you wish to change the hour, press CHANGE, if not press NEXT
Once you pressed the CHANGE button the hour is erased allowing you to enter the new time - enter the new hour in 24 hour format, when OK press NEXT
Once you pressed the NEXT button the minutes display;
If you wish to change the minutes, press CHANGE, if not press NEXT
Once you pressed the CHANGE button the minutes are erased allowing you to enter the new time - enter the new minutes, when OK press NEXT
Follow the same procedure for changing the date!
Programming template

Print this page, cut out the shaded areas with a utility knife and then cut around the outside box. After you're done cutting, place the template over the top 2 rows on your 7310 or 7324 telephone.


________________________________________
Panasonic XDP 824/1232 Back
All programming is done at ext. 101
(To Get This Document In PDF)

This procedure is to be done from a display phone at ext. number 101 or from a designated manager extension. The first step is to put that extension into a ?user programming? mode.

Notes about programming mode:
- When in ?programming? mode some of the phone buttons have different functions

- On a digital display phone, there are three buttons located under the display.

- When in ?programming? mode, the display shows labels for these buttons for the main functions
needed, for example ?->?, NEXT, or SEL (select).

- If you get mixed up, or when finished, get out of programming mode by picking up the handset
and hanging it up again.

- Some phones have a ?Program? button in the upper left, some have it on the bottom row above
the number 3, -if the phone does not have one, then use the button labeled ?Pause?.

- If you wait too long between pressing buttons, the system may cancel programming mode and
you will have to start all over

From Ext. 101:

1) Press PROGRAM button
2) Press **1234
3) Display reads <USER-PGM NO?>
4) Dial 0 0 0 (three zeros, not the letter O)
5) Display reads <Day/Time Set>
6) Press NEXT (same as SPKR PHN)
7) Display now shows date (if you need to change the date, see steps 10 thru 15 below)
8) Press NEXT (SPKR PHN) again
9) Display now should show time (example 12:00 AM)
10) Enter the hour on your keypad (to change current entry press CLEAR, or the TRANSFER button)
11) Press -> (or FWD/DND button)
12) Enter the minutes
13) Press -> (or FWD/DND button)
14) Press SELECT (or AUTOANSWER/MUTE button) to change AM or PM
15) Press STORE (or AUTODIAL/STORE) ***Don?t Forget This Step***
16) Press END (or HOLD button)
17) Press SPKR PHN button or pick up handset and hang up to exit programming mode.
Panasonic KXT 308/616
All programming is done at ext 11
1) At control unit, switch button to program position
2) Dial 00
Panasonic DBS 824, 40, 72 & 96
- From the Attendant's display phone.
1. Press "On/Off"
2. Press "Prog"
3. Press " ##"
4. Press "FF1 key"
5. Dial 1#, 2#
6. Dial the time in 24 hr format.
7. Press #
8. Press "On/Off"
- From any display phone in the system.
1. Press "On/Off"
2. #98 + Password
3. Press "Prog"
4. Press " ##"
5. Press "FF1 key"
6. Dial 1#, 2#
7. Dial the time in 24 hr format.
8. Press #
9. Press "On/Off"
Panasonic DBS 576 & 576 HD
From any display phone in the system;
1. Press On/Off
2. Press "Prog"
3. Press " * * "
4. Dial the " Password"
5. Press "FF8"
6. Dial 81001
7. Dial in new time in 24 hr format.
8. Press Hold and then "On/Off"

________________________________________
SAMSUNG-PROSTAR DCS Back
Should it ever become necessary to change the date and time displayed on all of the keysets, do it as soon as you notice theat they are incorrect. Automatic Night Service will not work correctly and SMDR records will be of no value when the date and time are not correct.
The Diplay Format is the Following
W (Day of the week): Enter 0 for Saturday
MM (Month): Enter 01 for January and 12 for December
DD (Day of the month): Enter a number in the range of 01 - 31
YY (Year): Enter the last two digits of the year
HH (Hours): Use the 24 hour clock and enter a number in the range of 00-24
MM (Minutes): Enter a number in the range of 00-59

Failure to enter the time using the 24 hour clock will cause the date to change a 12:00 pm Open customer porgramming and follow the instructions below.

Press TRSF and then dial 505 Display will show OLD: 6010184:0047 NEW: WMMDDYY:HHMM
Enter the new time and dat using the above format
Verify the time and date and re-enter them if necessary
Press TRSF to store and exit programming or press SPK to store and advance to next program

If you have entered invalid data, you will receive an [INVALID ENTRY] message for three seconds. Re-enter the correct date and time. If the information you entered is incorrect again, repeat the procedure.

SAMSUNG-PROSTAR 816
To Enable Customer Programming
With the handset on-hook, dial '#06'. The display shows [MMC DISABLED].
Dial the passcode and '1' then dial '#'
Password 4321
At this point, the customer programming is open
Setting the Time and Date
After you have enabled customer programming, you may begin the following steps:
Dial '#55'. Display shows[YY MM DD HH MM]
Dial new information as follows:
YY = Last two digits of the year
MM = Month (01 - 12)
DD = Day of the month (01 - 31)
W = Day of the week (1 -7 day of the week begins on Monday & ends on Sunday)
HH = Hour (Use 24 hour clock)
MM = Minutes (0-59)

Dial '#' to set current time & date. The phone returns to normal use
SAMSUNG-PROSTAR 56/120
Before any programs can be accessed, you must first open system programming using the passcode you have been assigned. This must be done using an 824 display keyset.
While on-hook dial '#20'
Display shows OPEN SYSTEM PGM - ENTER CODE: Display four digits passcode (1234). Display shows OPEN SYSTEM PGM - CLOSED
Press MUTE key. Display shows OPEN SYSTEM PGM - OPENED Press '#'. Keyset returns to idle condition.
Now press '#' and two digit program code you want to access. Follow the instructions for that program
Note: You must begin programming within 60 seconds. ONce in programming, any delay of more than 60 seconds between keystrokes will cause the system to automatically close programming.
Should it ever become necessary to correct date and time displayed on all the keysets, do so as soon as it is noticed that it is incorrect. Traffic reports and SMDR records will be of no value when the date and time are not correct.
Diplay Format:
W (Day of the week): Enter 0 for Saturday
MM (Month): Enter 01 for January and 12 for December
DD (Day of the month): Enter a number in the range of 01 - 31
YY (Year): Enter the last two digits of the year
HH (Hours): Use the 24 hour clock and enter a number in the range of 00-24
MM (Minutes):
Enter a number in the range of 00-59

Note: Failure to enter time in 24 hour clock will cause the date to change at 12:00 noon

First open customer programming

ACTION

Dial '#70' Display Shows SET CURRENT TIME YY MM/DD W HH:MM
Enter current date & time, e.g., 3:15 pm, Mon Jan 6th 1992 SET CURRENT TIME 92 01/06 1 15:15
Press '#' to store and exit If you entered invalid data, you will receive the [INVALID ENTRY] message for three seconds.
Re-enter the correct date and time. Should the information that you entered be incorrect, repeat the procedure

SAMSUNG-PROSTAR 1224
Before any programs can be accessed, you must first open system programming using the passcode you have been assigned. This must be done using an 824 display keyset.

While on-hook dial '#20' Display shows OPEN SYSTEM PGM - ENTER CODE:
Display four digits passcode (1234). Display shows OPEN SYSTEM PGM - CLOSED
Press MUTE key. Display shows OPEN SYSTEM PGM - OPENED
Press '#'. Keyset returns to idle condition.
Now press '#' and two digit program code you want to access.
Follow the instructions for that program

Note: You must begin programming within 60 seconds. Once in programming, any delay of more than 60 seconds between keystrokes will cause the system to automatically close programming.
Should it ever become necessary to correct date and time displayed on all the keysets, do so as soon as it is noticed that it is incorrect. Traffic reports and SMDR records will be of no value when the date and time are not correct.
Diplay Format:
W (Day of the week): Enter 0 for Saturday
MM (Month): Enter 01 for January and 12 for December
DD (Day of the month): Enter a number in the range of 01 - 31
YY (Year): Enter the last two digits of the year
HH (Hours): Use the 24 hour clock and enter a number in the range of 00-24 MM (Minutes): Enter a number in the range of 00-59
Note: Failure to enter time in 24 hour clock will cause the date to change at 12:00 noon First open customer programming
ACTION
Dial '#70' Display Shows SET CURRENT TIME YY MM/DD W HH:MM
Enter current date & time, e.g., 3:15 pm, Mon Jan 6th 1992 SET CURRENT TIME 92 01/06 1 15:15
Press '#' to store and exit

If you entered invalid data, you will receive the [INVALID ENTRY] message for three seconds. Re-enter the correct date and time. Should the information that you entered be incorrect, repeat the procedure.

________________________________________
Telrad Analog Systems Back
Time Set for Telrad Analog 816 and 2464
Enter from the time set station (usually 20)

Example Used: January 18, 2002, 2:00 pm
Remember, this is just an example, use the actual date and time!
Press ?SPKR?
Press the # key
Press the ?time? button
Dial date 18 (2-digit date)
Dial month 01 (2-digit month)
Dial military time 1400
Press ?TIME?
Press ?SPKR?

Digital systems

From time setting station (usually 20 or 200)

Time Set for Telrad Digital 818, S60, 128, 400 and S1000

Large Expanded Display

Press (PROGRAM)
Press (TIME)
Dial correct time using HHMM 24 hour format
Dial correct date using DDMMYY
Press (SAVE)

Small Display

Example Used: January 18, 2002, 2:00pm
Do Not Pickup the Receiver!!
Remember, this is just an example, use the actual date and time!
Press Feat 82
Then dial all in succession
Dial military time 1400
Dial day 18
Dial month 01
Dial year 02
Press spd/pgm? to save changes


What about the voice mail?

If the voice mail date is still wrong, go to the voice mail computer and press
"F10" to exit the voice mail program. At the cd\ prompt type "time". Follow the
existing format that is on the display and enter the new time. Press enter. When complete, make sure you type vm at the c:\ prompt, then press enter to bring the voice mail program back on at the Main Applications Menu which is where it should be.




________________________________________
Toshiba Strata VI XII & XX E Back

From Station 10
1. Push RDL, then SDS
2. Dial 51 for date
3. Dial 52 for time
4. Dial 53 for day
Toshiba Strata DK8, DK16, DK24, DK56, DK96
1. From main console phone (lowest extension number i.e. x100) pick up handset and dial following codes:
2. For Date: 651 YYMMDD Redial ----(YY=year, MM=month, DD=day)
3. For Time: 652 HHMMSS Redial ----(HH=hours in 24hr clock, MM=minutes, SS=seconds)
4. For Day of Week: 653 X Redial ----(X=day of week 1=sunday, 2=monday....etc.)

________________________________________
Trillium Panther II Back
(From Master Attendant Only)
1. Press "Program" key and dial 07
2. Enter a 2-digit HOUR (military time i.e. 15 for 3pm)
3. Enter a 2-digit MINUTE (00-59 i.e. 10 for 3:10)
4. Press "*" to exit programming mode

________________________________________
Vodavi Digital Back
Programming must be done from the first attendant station.

1. From Intercom dial tone dial "692YYMMDDHHMM" where 692 = set time code, YY= year, MM= month, DD=date, HH=hour in 24 hour format, MM=minute.
2. B. After typing that in you will hear a beep and the time will be changed.

Vodavi DHS
From any display telephone enter Attendant Administration. Press:
FEAT # 0
The display will then prompt you for the password (Chk Pswd:). The default password is 0000. Dial:
0000
Press the top soft key that corresponds to save.
save
The display will then prompt you to select the function you desire. Press the top soft key that corresponds to time.
time
The display should read SYSTEM TIME.
show
The display will display the current programmed year. To change the year press the soft key that corresponds to chg otherwise hit next.
next
The display will display the current programmed month. To change the month press the soft key that corresponds to chg otherwise hit next.
next
The display will display the current programmed day. To change the day press the soft key that corresponds to chg otherwise hit next.
next
The display will display the current programmed weekday. To change the weekday press the soft key that corresponds to chg otherwise hit next.
next
The display will then display the current programmed hour. To change the hour press the soft key that corresponds to chg otherwise hit next.
chg
Dial the current hour in military/24-Hour time. (Ex: 3PM = 15, 3AM = 03)
xx (where xx = current hour 00-23)
save
next
The display will display the current programmed minute. To change the minute press the soft key that corresponds to chg otherwise hit next.
next
The display should now read SYSTEM TIME. You have now successfully completed the time change. Press the CLEAR button to return to normal telephone functions.
CLEAR
Starplus 308EX, 616FLEX and 1224EX

From the programmed Attendant Station (station 10 by default), do the following:

1. Press the Speed button.
2. Dial the asterisk (*).
3. Dial 50 on the keypad. (The display will read "System Speed Bin 50")
4. Dial year, month, day (in double digits) and hours and minutes in military time (2400 hours).
5. Press hold. Confirmation tone will be heard and Display will update to the idle position with the correct time and date.
6. Press the on/off button to turn the set off.

________________________________________
ZT-D Telephone System Back

You must change the time from the Attendant telephone:
1. Lift the receiver
2. Press [FEAT] [#] [2]
3. Dial the time in Military Time
4. Hang up You must change the date from the Attendant telephone:
5. Lift the receiver
6. Press [FEAT]
7. Press [SPKR]
8. Press [2]
9. The display will show MM DD YY WEK
10. Enter two digits for the month, two digits for the day, two digits for the year, and two digits for the weekday.
11. Hang Up
• MM=Month
• DD=Day
• YY=Year
• WEK=Day of Week
• 78=Sunday
• 66=Monday
• 88=Tuesday
• 93=Wednesday
• 84=Thursday
• 37=Friday
• 72=Saturday